Chuck aa0hw's Blog – February 2020 Archive (9)

20 Watt VLF QRQ CW transmitter(18.200 Khz) - AD5DZ CW Keyer, Audio Amp, 4 to 1 Balun, Delta Loop

Brief experimental setup using the AD5DZ CW KEYER, to directly send 18.200 Khz CW AUDIO to a 20 watt audio amp...from the audio amp output to a large BLUE IRON POWDER TOROID 4 to 1 balun - then to the input of a compact 21 foot long DELTA LOOP wire antenna with one leg of the delta loop connected to a series resonant capacitor(6uF)

This 4…

Continue

Added by Chuck aa0hw on February 20, 2020 at 4:44pm — No Comments

Narrow Band QRQ CW filter, 50 hz wide, 2 APP combo to get rid of ringing & howling - 50 wpm test

this is an experimental test setup to get rid of narrow band CW filter SEA SHELL BACKGROUND HOWLING, and QRQ CW Ringing...

by using a:



1. SIMPLE GATE

2. SIMPLE CW BANDPASS FILTER

the gate silences the "in between" cw element sea shell howling, and ringing, but also causes key clicks...

the following CW BANDPASS…

Continue

Added by Chuck aa0hw on February 18, 2020 at 12:16pm — No Comments

VLF Transmitter(delta loop) - VLF Receiver(Ferrite Core Bipolar Tesla Coil) - QRQ CW demo

brief demo of testing a VLF TRANSMITTER and VLF RECEIVER for QRQ CW operations

this is a follow up video to the first two using a VLF RECEIVE - BIPOLAR TESLA COIL with a FERRITE CORE antenna...the Transmitter is a tiny DELTA LOOP(7 foot per side) fed by a 5 watt audio amp…

Continue

Added by Chuck aa0hw on February 16, 2020 at 2:19pm — No Comments

Windows 10 laptop, transmitting @ 8 Khz on VLF band, QRQ CW @80 wpm - Received on Linux Laptop using SAQrx SDR RCVR

this is a follow up video to the first one:

https://youtu.be/ON-tZWiCCPQ...

everything is the same in this video, except, this time we send QRQ CW at 80 wpm to test how it will sound over VLF and using SAQrx by itself - using its 300 hz wide bandpass filter - centered at 700 hz

and with…

Continue

Added by Chuck aa0hw on February 14, 2020 at 12:43pm — 1 Comment

Receiving a QRQ CW signal on VLF using QUISK SDR and wire antenna attached to sound card input

brief demo showing QUISK SDR and a wire antenna hooked up to the PC's sound card input
- picking up a weak QRQ CW signal on VLF - 18 khz

- by using the AGC on QUISK SDR and sending the QUISK SDR receive audio through the CALF EQ 5 BAND lv2 plugin, the weak signal is brought up significantly to improve copy

Added by Chuck aa0hw on February 12, 2020 at 3:25pm — No Comments

QRQ CW LAB - Testing a REMOTE RIG CW KEYING setup using a Raspberry PI::Rig interface

REMOTE RIG QRQ CW KEYING - over ip - using Gstreamer scripts on a Raspberry PI 2b::RIG hardware interface, and a remote OP's Linux laptop, on the local area network, wired Ethernet, going through a Router and network switches

NETWORK CONDITIONS = poor

ROUTER = 20 yr old router, 100 mb limit...

ETHERNET CABLES = two "CAT 4" - 100…

Continue

Added by Chuck aa0hw on February 8, 2020 at 3:30pm — No Comments

Gstreamer 1 line of code to produce a 2 tiered, 2 tone, final bandpass filter for CW & PTT - AFCW - QRQ CW demo

brief demo of QRQ CW testing a Gstreamer CLI 1 liner - to get two different audio bandpass filters at the same time, staggered, and incremental, for their respective tones of 707 hz and 5555 hz

GSTREAMER CODE used in this BANDPASS FILTER TEST

**********************************************************

gst-launch-1.0 -v interleave…

Continue

Added by Chuck aa0hw on February 4, 2020 at 2:38pm — No Comments

Remote QRQ CW over ip operations using multipurpose Gstreamer Scripts - laptop to Raspberry PI::RIG interface

Several Gstreamer scripts are used to perform REMOTE QRQ CW KEYING of a RIG(afcw mode) from the REMOTE OP's location using TCP audio over ip network packets through a router and network switches in the pathway(WIRED ETHERNET)

there are 2 Gstreamer BANDPASS filters applied before audio goes to rig for transmit:

1. 680 hz BPF Gstreamer…

Continue

Added by Chuck aa0hw on February 3, 2020 at 1:20pm — No Comments

Get better audio quality from the Elecraft K3S QRQ CW SIDETONE MONITOR - using the Noise-Repellent plugin

https://github.com/lucianodato/noise-repellent

An lv2 plugin for broadband noise reduction

brief demo showing how noisy the ELECRAFT K3S transmit audio input monitor circuit is....and how well the Noise-Repellent LV2 Plugin takes out virtually all of that K3S background noise,…

Continue

Added by Chuck aa0hw on February 3, 2020 at 10:44am — No Comments

Monthly Archives

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

© 2024   Created by Chuck aa0hw.   Powered by

Badges  |  Report an Issue  |  Terms of Service