August 2022 Blog Posts (13)

ZAMGATE SIDECHAIN GATE mode does the ENCODING and DECODING

encoder uses the RECRI OSCILLATOR SDR MODULE at ZERO HERTZ as the CW DATA KEYING INSTRUCTIONS ENCODER https://github.com/recri/keyer

CW RE-KEYER:

ZAMGATE…

http://jack-rack.sourceforge.net/

USES GSTREAMER script for both the SENDER and RECEIVER SEND 4Khz, 12Khz OR 20Khz to RX OP

here is the example using 4Khz

gst-launch-1.0 -v audiotestsrc freq=4000 ! audioconvert ! opusenc ! rtpopuspay ! udpsink host=(ip address of the RX OP) port=9999

RECEIVE OP script: gst-launch-1.0…

test to see how well a Pi4 MUMBLE iCW setup can handle all the apps it takes to setup up a MUMBLE INPUT and OUTPUT cw audio morse code RE-GENERATOR SYSTEM

80wpm QRQ CW test

https://sites.google.com/site/icwoip/

CARLA PLUGIN…

GLAME BANDPASS FILTER   http://plugin.org.uk/ladspa-swh/docs/ladspa-swh.html

iCW/mumble   https://sites.google.com/site/icwoip/

Carla Plugin HOST …

Brief Demo for sending QRQ CW over SONOBUS using KXstudio's Carla in "multiple clients" mode on a Raspberry Pi 4 SonoBus is also monitoring its input to be able to monitor the REGEN'd ZamGate CW sidetone in real time at near zero latency

a TLC555 is being keyed by FLdigi's serial port rts pin, TLC555 sending its audio…

https://github.com/gordonjcp/lysdr

i/q encoding of CW Signals from -3kHZ to -30kHZ & +3kHZ to +30kHZ was done with 12 CW KEYBOARD from RECRI KEYER…

http://www.4sqrp.com/hipermite.php

to reduce the unwanted harmonics & QRQ CW edge noise generated by a keyed TWIN-T's CW audio output...the HI-PER-MITE active audio cw filter is tested to see how well it cleans it up

\

this setup uses the following hardware:

1. raspberry pi 4

2. TLC555 that is keyed by a CW KEYER's RIG KEYING jack...(the TLC555 is powered by the PI's own 3.3v power supply via its GPiO pins

3. usb sound card with LINE INPUT - this demo uses a Behringer UCA222 the keyed 555's audio…

test using bpsk31 over ip from one op to the other to coordinate frequencies for HF QSO NOTE: NO AUDIO is heard on this video demo....visual only FLdigi provies the ENCODING and DECODING of bpsk31 Gstreamer provides the OPUS codec encoding to convert bpsk31 from and to one OP to the other here are the scripts used in this example…

this video is a follow up to the first video here: https://youtu.be/RQh_4JW6adw

this video adds a CW KEYBOARD, and straight key to the Raspberry PI 4 iambic CW keyer shown in the first video... by using a 2nd keyed CPO at a different PITCH than the 1st keyed CPO in…

TLC555 timer chip square wave oscillator is being 'keyed' (pin 4/pos rail) by a CW KEYER & its iambic paddles AND also being keyed by FLdigi using FLdigi's serial port keying setup via a usb serial port adapter and keying the serial port's RTS PIN Both the CW KEYER and FLDIGI are keying the diode side of an H11F1 FET OPTOisolator chip and…

snd-aloop

alsa-loopback cable

virtual audio cable

via a Gstreamer TEE SCRIPT to take a keyed oscillator at the mumble sound card input... filter it 1st... and then send it to two places...

1. the mumble USB sound card's output so you can monitor your own…